SMX921 Repeater
P25 Digital Repeater Two-way Radios
The S and SD Series, low current Repeater and Base Station solutions, are designed from the ground up for the absolute lowest power consumption and features the lowest current draw of any professional high performance Repeater/Base Station on the market today. Advanced circuit design and optimization is demonstrated by the very high level of RF performance achieved while maintaining very low power consumption levels. The S & SD set a new industry benchmark by avoiding dated techniques that try to save power wasted by constantly duty cycling the receiver on and off or degrading the RF performance to unacceptable levels. The S & SD do not sacrifice any of these critical requirements and achieves a level of performance that competing products can provide at any power consumption level. Available as a Base Station or Repeater, in Analog Conventional (SMX) or P25 Digital (SDMX) (with LZAST92 P25 Option).
Call for price and options: 541-621-4588
SMX921 FEATURES
- Very Low current consumption
- No need for receiver duty cycling
- System Interface
- Fully Programmable / Configurable via PC or serial device
- Remote controllable Multi tone CTCSS community decoder
- 100% full power duty cycle
- 5 Tone signaling
- High Accuracy Real Time Clock.
- Multi staged TX VF processing with triple limiters
- Flash Firmware Upgrade Capable
- Battery backup system option
- Built In Test Equipment (B.I.T.E.) and remote diagnostics
- Broad Band High Efficiency LDMOS PA module
- RX & TX Switching BW covers full sub band
- Fast Serial Data Interface
- Full Digital alignment and calibration
- Field interchangeable PA module needs no re-alignment
- Pre calibrated power and deviation alignment. Digital value
- Low RFI and EMI emission design
- Controlled TX RF envelope
- DTMF decoder
- DTMF Remote control
- Latest technology, full SMD
- Advanced and optimized RF design
- High performance 16 bit Flash processor
- Programmable 12.5/25kHz channel spacing
- Configurable Function Front Panel LEDs
- Low current LEDs with digital intensity control
- Simple and fast disassembly for service
- Precision internal shielding system
- Minimal technician adjustments for future maintenance
- Design spec –40 to 70 degrees C
- Low aging oscillators
- Universal microphone input circuit
- Minimal interconnections
- Options can be easily retrofitted
- Minimal mechanical adjustments
- Front end RX filter never needs realignment
- Built in TX modulation alignment audio oscillator
- Built in auto alignment software guides technician
- Fast and simple disassembly
- Built on proven technology
- Configuration password protected
- Virtual elimination of internal wiring
- Elimination of helical filters, quadrature coils, MCF matching and trim potentiometers
- System independent, no additional software program required
SMX921 OPTIONS
- P25 Repeater Option Board
- LZAST92
- Transparent Mode:
- Repeats Mixed Mode, P25 Digital and Analog transmissions.
- Automatically switch to P25 mode on reception of P25 carrier.
- Passes P25 NAC unchanged.
- Passes P25 private call and group call.
- Passes P25 clear or encrypted.
- Front panel indicators show P25 status.
- Benefits of Digital Audio Performance.
- Design based around proven architecture.
Additional Options
- Desk Mic/Palm Mic
- Internal Simplex relay
- Virtual PC Console including:
- ANI/CTCSS/DCS/5TONE/DTMF display
- Solar panel and battery power management system option board.
- Universal system interface
SMX921 SPECS
- GENERAL SMX921
- Frequency Bands
- Band D3 148-174 MHz
- Band L3 350-385 MHz
- Band N2 400-435 MHz
- Band O2 435-470 MHz
- Band P2 450-485 MHz
- Band Q 485-520 MHz
- Synthesis Method Non mixing PLL Fractional N synthesizer
- Modulation Direct FM two point method
- Channel Spacing Programmable 25kHz / 12.5 kHz
- Synthesizer Step Size 6.25kHz or 5kHz auto select
- Channels
- 100 front panel selectable, 255 PC software selectable
- Supply Voltage 13.8 +/- 20%
- Operating Temperature -30 to +60C
- Dimensions (W x D x H) 2RU Case, 325mm deep including fan
- Standard LED indicators Power, RX, TX, Tone, Alert, Repeater
- Standard Switches Two press button type
- Standard Controls Volume knob, Squelch screwdriver adjust.
- Interface Front panel Microphone accessory socket, speaker, rear connector DB25. Location for DB9 x 2, DB15, RJ45.
- Weight 8kg.
RECEIVER
- Measured in accordance with TIA/EIA-603 Standards
- Sensitivity Better than -120dBm for 12dB SINAD, Typical -123dBm
- Selectivity 135-520 MHz More than 85dB for 25kHz adj channel, Typical 90dB more than 75dB for 12.5kHz adj channel
- Audio Bandwidth 300 Hz to 3000Hz (+1,-3dB)
- Image Freq Rejection Better than 100dB
- Spurious Response Immunity Better than 82dB, Typical 84dB
- Intermodulation Immunity Better than 82dB (WB), 80dB (NB)
- Blocking Better than 100dB at +/- 1MHz point
- Distortion Less than 2% @ 60% deviation
- S/N Ratio Better than 50dB (WB)
- Better than 44dB (NB)
- Co-Channel Rejection Better than 5dB
- RF Switching Bandwidth Equal to Sub band allocation
- Receiver Front End BW Equal to Sub band allocation
- Receiver Audio Power 1 Watt
TRANSMITTER
- Measured in accordance with TIA/EIA-603 Standards
- RF Power Output 1W to 50W variable,
- 0.1 to 2W* UHF PA opt (1W nominal)
- Frequency Stability >300MHz
- <300MHz 1.5PPM for –10 to 60C 2.5PPM for –30 to -10C
- 2.5PPM for –10 to 60C 5PPM for –30 to -10C
- Audio Response Flat within +1, -3dB across BW
- Audio Bandwidth 300Hz to 3000Hz.
- Modulation Distortion Less than 2% @ 60% deviation
- S/N Ratio Better than 50dB (WB)Better than 44dB (NB)
- Conducted Spurious Emissions Better than -90dBc
- Conducted Harmonic Emissions Better than -90dBc
- RF Switching Bandwidth Full Sub band
- RF Switching Bandwidth PA Full Sub band
- Duty Cycle 100% for 50W RF output
- RF Rise Time <50mS with VCO in cold standby